Mbm-corporation AEROCUT Bedienungsanleitung

OPERATION MANUAL UCHIDA YOKO CO., LTD., TOKYO, JAPAN Jul 14, 2011 USA

(3) Installation 1. The machine installation method UnlockLockPlease be sure to LOCK a caster brake after making it move to the target position, when

3. How to remove accessories ① Remove the chute screws. ② Lift the chute and take out the waste box. ③ The accessory case is inside the waste box.

2. Operating instructions (1) Checks before use Check the following before operation. ① Is the electric power turned off? ② Is the feed ta

(3) Waste box setting ① Set the waste box under the stacker. Waste box Chute Caution Power it off. Otherwise, １２ Injury coul

(5) Paper setting ① Press SET to lower the feed table. ② Separate the sheets of paper well and place them on the feed table. ③ Fix the paper with t

(6) Paper slant adjustment ① When the printing is tilted, turn the dial as shown in the drawing below to make it straight. ② Turning the dial counte

(8) How to attach the perforator ① Power it off. ② The perforator is stowed below the feed table. ③ Detach the gear cover located at the paper ex

(9) How to adjust the perforation location ① When using the perforator, the screen will display where to fix the perforator, as shown below. ② Set

(10)How to adjust the depth of perforation ① Change in the paper thickness, recommend you adjust the depth of Perforation. ② Loosen both lock leve

3. Operational method (1) Basic operation ① Turning the power on. ② Slitter initial location movement (When turning the power on initially and afte

• Use machine only after reading the "Safety Instructions" given below carefully. • These safety instructions are given to ensure that the

(3) Format selection ① Press PRESET. ② Select the paper type to be used. Operation Screen Return to Operation ScreenPaper Select

④ Cutting pattern content confirmation and partial correction Press A through N to make corrections. O,P and M are automatic calculations. It is pos

(4) Free entry ①Press MANU SET. Operation Screen ② The operation is almost the same as (3)-④. (5) User program retrieval ① 50 us

(6) User program registration ① 50 user program can be registered. ② Press the button in which you wish to make a registration. ③ Confirm

(7) Setting of slitter and feed table ① By pressing SET, the feed table will be lowered to the bottom dead point and the slitter will move to the ope

(9) Manual operation ① Press MANUAL. Operation Screen ②Use it when operating manually. Return to Operation Screen Move to Adjust

(10) Speed change ① Press SPEED from the Operation Screen. Operation Screen ② There are eight feeding speed levels. The currently selected

(11) Cut mark on/off selection Select C/MARK ON to use cut marks. Select C/MARK OFF for not using cut marks. Operation Screen (12) Automatic o

4. Instructions for use (1) If the machine stops during operation ① If the machine stops during operation due to an error such as a paper jam and ov

(2) If Paper scrap remains on the machine ① If paper scrap remains behind Stacker panel. If paper scraps remain in the Crease part of machinery, turn

SAFETY INSTRUCTIONS Explanations of the illustrations used in the Safety Instructions are given as follows: Danger 1. Don't open the cover of

(3) Details concerning errors ① Paper size error Correct the paper size to fit in the value range below. ② Final cutting measurement error

⑥ Top margin error Correct the top margin to fit in the value range below. ⑦ Back margin error Correct the back margin to fit in the value spe

⑪ Perforation location warning Correct the perforation location to fit in the value range below. The maximum value is subject to change depending on

⑯ Timeout error 2 Paper did not pass through within a set time period. Remove the paper remaining inside the machine. ⑰ Overload error 1 Cutt

Paper length variation or double feed detection error Paper lengths vary. Check the paper. Slitter units positioning error Slitte

(4) If the cut measurement does not match the input value ① If Measurement A is different: When the input value is 0.200” and the actual cut measure

5. Product specifications Specifications Slitter 4 sets (6 slitter blades) Creaser 1 set (5-level manual crease depth adjustment) Perforator 2 set

①Paper size ②Finish size ３６ ③Limitations ④Cut mark size and position ⑤Crease limitations（Max. four times）

6. Equipment, Electric circuit and parts ３７

３８ ３８

Caution 1. Don't put a hand into the cover or a clearance between parts. There is a danger of receiving an injury. 2. Don't bring a ha

３９ ３９

7. Ordering consumables, etc. When ordering consumables or parts, be sure to specify the machine model. ４０

OPERATION MANUAL ４１ If this “Operation Manual” is stained or lost, make contact with thedistribu

４ Introduction Read this "Operation Manual" carefully before use. In particular, be sure to read "Safety Instructions" (page 2

５Contents 1. Before use...

1. Before use (1) Description and quantities of accessories Electric power cord 1pc. Hexagonal wrench 0.08” X 1pc. Tweezers 1pc. Waste ejector 1pc.

(2) Exterior features 1. Name of parts 4 5 6 7 8 109 1 3 2 1. Stacker 6. Slitter 2. Touch Panel 7. Feed Table 3. Crease Depth

2. Electric-power-related points The electric power switch and the inlet are located inside the machine, below the feed table. 2 1 3